Wikizone - Benutzerbeiträge [de]

Arduino

2012-03-18T12:51:13Z

79.240.81.219: /* Programmieren */

== Bezugsquellen ==

==Programmieren==
Beispiele http://arduino.cc/en/Tutorial/HomePage
===Basic Structure===
<pre>
void setup() {
// put your setup code here, to run once:

}

void loop() {
// put your main code here, to run repeatedly:

}
</pre>

==Midi==
http://arduino.cc/en/Tutorial/Midi

<pre>
/*
MIDI note player

This sketch shows how to use the serial transmit pin (pin 1) to send MIDI note data.
If this circuit is connected to a MIDI synth, it will play
the notes F#-0 (0x1E) to F#-5 (0x5A) in sequence.

The circuit:
* digital in 1 connected to MIDI jack pin 5
* MIDI jack pin 2 connected to ground
* MIDI jack pin 4 connected to +5V through 220-ohm resistor
Attach a MIDI cable to the jack, then to a MIDI synth, and play music.

created 13 Jun 2006
modified 30 Aug 2011
by Tom Igoe

This example code is in the public domain.

http://www.arduino.cc/en/Tutorial/MIDI

*/

void setup() {
// Set MIDI baud rate:
Serial.begin(31250);
}

void loop() {
// play notes from F#-0 (0x1E) to F#-5 (0x5A):
for (int note = 0x1E; note < 0x5A; note ++) {
//Note on channel 1 (0x90), some note value (note), middle velocity (0x45):
noteOn(0x90, note, 0x45);
delay(100);
//Note on channel 1 (0x90), some note value (note), silent velocity (0x00):
noteOn(0x90, note, 0x00);
delay(100);
}
}

// plays a MIDI note. Doesn't check to see that
// cmd is greater than 127, or that data values are less than 127:
void noteOn(int cmd, int pitch, int velocity) {
Serial.write(cmd);
Serial.write(pitch);
Serial.write(velocity);
}
<pre>

Arduino

2012-03-18T12:50:26Z

79.240.81.219: /* Programmieren */

Arduino

2012-03-18T12:31:15Z

79.240.81.219: /* Programmieren */

== Bezugsquellen ==

==Programmieren==
Beispiele http://arduino.cc/en/Tutorial/HomePage

==Midi==
http://arduino.cc/en/Tutorial/Midi

<pre>
/*
MIDI note player

This sketch shows how to use the serial transmit pin (pin 1) to send MIDI note data.
If this circuit is connected to a MIDI synth, it will play
the notes F#-0 (0x1E) to F#-5 (0x5A) in sequence.

The circuit:
* digital in 1 connected to MIDI jack pin 5
* MIDI jack pin 2 connected to ground
* MIDI jack pin 4 connected to +5V through 220-ohm resistor
Attach a MIDI cable to the jack, then to a MIDI synth, and play music.

created 13 Jun 2006
modified 30 Aug 2011
by Tom Igoe

This example code is in the public domain.

http://www.arduino.cc/en/Tutorial/MIDI

*/

void setup() {
// Set MIDI baud rate:
Serial.begin(31250);
}

void loop() {
// play notes from F#-0 (0x1E) to F#-5 (0x5A):
for (int note = 0x1E; note < 0x5A; note ++) {
//Note on channel 1 (0x90), some note value (note), middle velocity (0x45):
noteOn(0x90, note, 0x45);
delay(100);
//Note on channel 1 (0x90), some note value (note), silent velocity (0x00):
noteOn(0x90, note, 0x00);
delay(100);
}
}

// plays a MIDI note. Doesn't check to see that
// cmd is greater than 127, or that data values are less than 127:
void noteOn(int cmd, int pitch, int velocity) {
Serial.write(cmd);
Serial.write(pitch);
Serial.write(velocity);
}
<pre>

Arduino

2012-03-18T12:12:21Z

79.240.81.219: Die Seite wurde neu angelegt: „ == Bezugsquellen == ==Programmieren== ==Midi== http://arduino.cc/en/Tutorial/Midi <pre> /* MIDI note player This sketch shows how to use the serial tra…“

== Bezugsquellen ==

==Programmieren==

==Midi==
http://arduino.cc/en/Tutorial/Midi

<pre>
/*
MIDI note player

This sketch shows how to use the serial transmit pin (pin 1) to send MIDI note data.
If this circuit is connected to a MIDI synth, it will play
the notes F#-0 (0x1E) to F#-5 (0x5A) in sequence.

The circuit:
* digital in 1 connected to MIDI jack pin 5
* MIDI jack pin 2 connected to ground
* MIDI jack pin 4 connected to +5V through 220-ohm resistor
Attach a MIDI cable to the jack, then to a MIDI synth, and play music.

created 13 Jun 2006
modified 30 Aug 2011
by Tom Igoe

This example code is in the public domain.

http://www.arduino.cc/en/Tutorial/MIDI

*/

void setup() {
// Set MIDI baud rate:
Serial.begin(31250);
}

void loop() {
// play notes from F#-0 (0x1E) to F#-5 (0x5A):
for (int note = 0x1E; note < 0x5A; note ++) {
//Note on channel 1 (0x90), some note value (note), middle velocity (0x45):
noteOn(0x90, note, 0x45);
delay(100);
//Note on channel 1 (0x90), some note value (note), silent velocity (0x00):
noteOn(0x90, note, 0x00);
delay(100);
}
}

// plays a MIDI note. Doesn't check to see that
// cmd is greater than 127, or that data values are less than 127:
void noteOn(int cmd, int pitch, int velocity) {
Serial.write(cmd);
Serial.write(pitch);
Serial.write(velocity);
}
<pre>